
Pleated filter paper on the output conveyor. Review the required pleat geometry against your filter drawing.
Automatic filter paper pleating with laser cutting and hot-melt adhesive application included as standard.

The PLM-350A prepares pleated filter paper for square air filters and ECO filter elements. Match the paper, pleat geometry and downstream assembly requirements to your filter design.

Pleated filter paper on the output conveyor. Review the required pleat geometry against your filter drawing.
Share your paper specification, pleat height, pleat count and finished pack dimensions. Suitability of each paper-and-size combination is reviewed for your application.
The listed width and height ranges are selection references. Confirm the required combination for your paper grade and product; the range endpoints do not establish that every combination is suitable.

Paper path and roller detail. Match the paper specification and roller tooling to your application.

Close-up of the pleated paper and adjacent adjustment mechanisms.
The PLM-350A includes laser cutting and hot-melt adhesive dispensing systems as standard equipment. The red head shown below is the laser cutting head; the metal nozzles dispense hot-melt adhesive.

Laser cutting and hot-melt adhesive dispensing systems are included as standard equipment.
Define the required cutting pattern, adhesive specification and application position against your sample. Confirm processing settings for the selected paper and adhesive.
Review the roller pattern and tooling against your sample. Confirm the heating zone and the paper supplier's temperature limits. The water-vapor device described below is intended to help reduce paper breakage during roller imprinting; review its suitability for your paper and supply configuration.

Workshop view of the PLM-350A with pleated paper on the conveyor.
Machine demonstration. Review the demonstrated material and configuration when discussing your application.
Published PLM-350A specifications. Confirm the final configuration and operating conditions for your application.
| Product Name | PLM-350A |
| Speed | 5–30 m/min (adjustable) |
| Conveyor Belt Speed | 0–5 m/min (adjustable) |
| Min. Paper Width | 90 mm |
| Max. Paper Width | 320 mm |
| Min. Pleat Height | 16 mm |
| Max. Pleat Height | 60 mm |
| Operating Temperature | Up to 300 °C |
| Heating Power | 8.5 kW |
| Transmission Power of Pleater | 0.75 kW |
| Conveyor Belt Transmission Power | 0.25 kW |
| Working Air Pressure | 0.6 MPa |
| Power Supply | 380 V / 50 Hz |
| M/C Weight | 1100 kg |
| M/C Size (L×W×H) | 7500 × 950 × 1750 mm |
Yes. Laser cutting and hot-melt adhesive dispensing systems are included as standard equipment on the PLM-350A. Confirm any additional cutting or conditioning equipment in your quotation.
Provide the paper grade, thickness or basis weight, coating or resin details and target pleat geometry. Discuss a representative material trial and agree the acceptance checks before selecting the setup.
This is the published working-speed range, not a guaranteed finished-pack output. Confirm the measurement point and accepted output for your paper and pleat geometry.
Request a tooling and adjustment schedule for your size range, including the parts supplied and the first-piece inspection criteria. Changeover time depends on the defined paper and size change.
Agree which rollers or other parts are included, which settings need adjustment, and how the first acceptable sample will be checked after changeover. Any changeover-time target should be agreed for a defined paper and size change.
The published supply is 380 V / 50 Hz with 0.6 MPa working air pressure. Confirm phase, total connected load, air consumption and installation clearance. Confirm which heating component the listed maximum of 300 °C refers to; it is not a recommended temperature for every paper or adhesive.
Confirm the temperature measurement point and the complete installed layout, including access and maintenance space. Other electrical configurations require technical confirmation.
Send your filter drawing or sample photos, paper specification, width, pleat height, target output, factory power supply and destination country. Include the required cutting pattern and adhesive application details.
For a material trial, discuss pleat dimensions, paper damage, adhesive application, accepted output and changeover checks. Trial availability and acceptance criteria are subject to agreement.
لحماية خصوصية المستندات ، يرجى الاتصال بنا للحصول على كلمة مرور التنزيل: [email protected]